Custom Bats Cricket Forum

Equipment => Bats => Bat Care => Topic started by: FattusCattus on March 18, 2015, 03:43:03 PM

Title: Edge-Rounding
Post by: FattusCattus on March 18, 2015, 03:43:03 PM: Would anyone care to give an idiot's guide to their edge-rounding techniques - particularly the bathtub method? Pictures would be especially useful.

Last time I tried the bath-tub method it left black marks on the edge of my bat, and the handle kept bashing Mrs Fattus in the armpit.
Title: Re: Edge-Rounding
Post by: simonmay5 on March 18, 2015, 03:48:21 PM: When I went to warsop they used the work top that you have in the kitchen as it hard and has a round edge it works well
Title: Re: Edge-Rounding
Post by: arsenal123 on March 18, 2015, 04:03:51 PM: Be careful though. I ended up mishaping the wood on my kitchen unit doing it. Shh, dont tell the missus!! :o :-[
Title: Re: Edge-Rounding
Post by: Neon Cricket on March 18, 2015, 04:18:50 PM: Haha should get yourself some marble worktops - work a treat for rounding the edges ;)
Title: Re: Edge-Rounding
Post by: Buzz on March 18, 2015, 04:40:01 PM: You can use the handle of your knocking in mallet as well as the bath tub
Title: Re: Edge-Rounding
Post by: Ayrtek Cricket on March 18, 2015, 04:41:25 PM: Quote from: Buzz on March 18, 2015, 04:40:01 PM
You can use the handle of your knocking in mallet as well as the bath tub

yep, ive used my mallet handle to do mine as like Fattus says sometimes the bath leaves a grey line down the edge of your bat. Either way the trick is to apply even pressure to the edges to compress and round them off evenly.
Title: Re: Edge-Rounding
Post by: Stumper on March 18, 2015, 05:21:57 PM: A really big heavy rolling pin works just nice for me.
Title: Re: Edge-Rounding
Post by: FvanN on March 18, 2015, 06:23:05 PM: Quote from: Stumper on March 18, 2015, 05:21:57 PM
A really big heavy rolling pin works just nice for me.

2nd the rolling pin :)
Title: Re: Edge-Rounding
Post by: patriotscreen on March 18, 2015, 07:23:56 PM: I use a piece of stainless steel tubing that has been chromed and polished. Solid as a rock and doesn't leave any marks.
Title: Re: Edge-Rounding
Post by: OwzatOllie on March 18, 2015, 09:18:24 PM: I just use the mallet handle
Title: Re: Edge-Rounding
Post by: RossViper on March 18, 2015, 10:08:54 PM: Hold the toe and the bottom of the Handel. The edge should be presented to the surface, at an angle, I.e neither the face or the edge are parallel to the bath top.
gently slide it back and fourth in a bow like action. Don't over do the pressure, particularly if there is a scuff sheet on the bat. Do 10 - 20 passes then swop edges. Repeat, increasing the pressure and decreasingly the passes, check the progress after every few passes.
Title: Re: Edge-Rounding
Post by: FattusCattus on March 19, 2015, 09:19:31 AM: Ross - I think it would be better if you posted a pictoral guide of your bath-rubbing.
Title: Re: Edge-Rounding
Post by: KIPPERS on March 19, 2015, 09:22:53 AM: Please dont
Title: Re: Edge-Rounding
Post by: ajmw89 on March 19, 2015, 09:53:59 AM: Make sure the tub is clean... The grey marks are probably the dead skin and soap residue on the bath!

I usually put a little linseed oil on the edge of the tub to aid lubrication (always do it without a scuff). I do about 15 passes on each edge, then swap, and repeat until the edges are firm and can't be dented with a mallet. usually takees about 15-20 mins. Don't put pressure on the handle, you don't want to break it!
Title: Re: Edge-Rounding
Post by: northernboy1987 on April 03, 2015, 09:55:40 PM: I'm in the mallet handle/grip cone club :)