Topic: RNS Larson bat - knocking do's and dont's? (Read 5257 times)

bigblue365 · « **Reply #15 on:** October 20, 2019, 12:53:13 AM »

Quote from: Jimmy Tieana on October 18, 2019, 11:08:46 PM

How many times is oiling (& how much) required?

2-3 times.

Yorkershire · « **Reply #16 on:** October 25, 2019, 01:55:31 PM »

Quote from: FattusCattus on October 16, 2019, 07:50:45 PM

DO'S - Knock it in absolutely loads

DON'TS - Forget to knock it in absolutely loads

Heed this wisdom!

bigblue365 · « **Reply #17 on:** October 25, 2019, 08:14:22 PM »

70 mins into knocking in process the right hander outside is cracking vertically. I uploaded the images here - https://imgur.com/a/0zcUI92
Not sure what to do next?

Mfarank · « **Reply #18 on:** October 25, 2019, 09:19:29 PM »

Quote from: bigblue365 on October 25, 2019, 08:14:22 PM

70 mins into knocking in process the right hander outside is cracking vertically. I uploaded the images here - https://imgur.com/a/0zcUI92
Not sure what to do next?

Clear sign of overdried willow. Superglue and sand it down. Then put a couple of layers of fibreglass edge tape and hope for the best

brokenbat · « **Reply #19 on:** October 25, 2019, 09:50:21 PM »

It�s not that bad at all. I wouldn�t jump to conclusions. Seems like heartwood - it can crack like that if you whacked it too hard. No big deal - just glue and sand. Edges seem nice and round now - I wouldn�t knock them more.

Jimmy Tiwana · « **Reply #20 on:** October 26, 2019, 12:44:03 AM »

Quote from: Mfarank on October 25, 2019, 09:19:29 PM

Clear sign of overdried willow. Superglue and sand it down. Then put a couple of layers of fibreglass edge tape and hope for the best

Agree. My SM I bought last year had an impressive ping even though it started disintegrating during the knocking in process

edge · « **Reply #21 on:** October 26, 2019, 08:47:59 AM »

Doesn't look like anything to worry about at all, make sure you're not going too hard too early with the knocking in. Finish the process and then give it a little sand down, it'll be fine.

bigblue365 · « **Reply #22 on:** October 31, 2019, 07:08:32 PM »

Followed brokenbat and edge advice(superglue and light sand) and finished 4 hrs knocking. Ping is good now and hoping it will further open up after few net sessions. Applied scuff sheet and edge tape - https://imgur.com/a/9ySeiFg

Psi · « **Reply #23 on:** October 31, 2019, 07:56:53 PM »

Looks very nice. I would also put edge tape up the edge by the label as this bit is quite susceptible to cracking if you edge it there (through bitter experience this afternoon. Edged a pull shot badly up near the label and it has dented /cracked my new bat. Now fixed with a steam iron, superglue and sanding. Edge sheet now applied 😂

t2ylo · « **Reply #24 on:** October 31, 2019, 08:02:11 PM »

That�s a nice looking stick

Author Topic: RNS Larson bat - knocking do's and dont's? (Read 5257 times)

bigblue365

Re: RNS Larson bat - knocking do's and dont's?

Yorkershire

Re: RNS Larson bat - knocking do's and dont's?

bigblue365

Re: RNS Larson bat - knocking do's and dont's?

Mfarank

Re: RNS Larson bat - knocking do's and dont's?

brokenbat

Re: RNS Larson bat - knocking do's and dont's?

Jimmy Tiwana

Re: RNS Larson bat - knocking do's and dont's?

edge

Re: RNS Larson bat - knocking do's and dont's?

bigblue365

Re: RNS Larson bat - knocking do's and dont's?

Psi

Re: RNS Larson bat - knocking do's and dont's?

t2ylo

Re: RNS Larson bat - knocking do's and dont's?